Read the instruction manual carefully before starting the pump. • These pumps may .. vid sådana tillfällen skyddas med någon form av hylsa. • Smörj samtliga. timely basis, you may not be able to vote by giving instructions to the depositary. Imsa transaction, to refinance existing indebtness of Grupo Imsa and Hylsa. Reporte Anual , Monterrey, Mexico: Hylsa. Oslo Manual: Guidelines for Collecting and Interpreting Technological Innovation Data, 3rd Edition, Paris.
|Published (Last):||10 October 2010|
|PDF File Size:||3.18 Mb|
|ePub File Size:||9.36 Mb|
|Price:||Free* [*Free Regsitration Required]|
Read all instructions before using the appliance.
JVC KW NT30E NT30[E] User Manual LVT A
Machine presentation Description 3 1 General Fig. Continously lit when start relay is activated. For that reason, the level controls are sealed with enamel paint. Door and door lock 29 Replacing hyls door lock 1. Level control Contents Control and fault tracing Fit the new motor without locking the mounting bolts.
When counter unit is for double slot, the lower value. No intente abrir la puerta hasta que la luz indicadora este encendida. Depending on the size of the machine, the following heating elements are available: The machine can also be fitted with steam heating using a steam valve fitted on the rear of the machine.
Sometimes it is sufficient to loosen it from the shaft. Undo the bracket for the manuxl hose connector from the lower rear piece, then hylxa the rear cover. If only one coin, all switches shall be set in OFF position. Pressure plate Recoil spring Cylinder Piston Lower part Diaphragm Nipple for connection of feed hose from control valve 6.
During normal operation, the LEDs blink when the drum is not turning and are off when the drum rotates. Then it is easier to mount the sealing rings.
In order to be able to put the puller blocks under the bearing, push the rear gable a little. Assemble in reverse order. A faulty level switch can not be repaired and should be replaced. Adjust drive belt tension if values exceed those shown in the table. Most mmanual are then presented in detailed in separate chapters in this service manual. Regular maintenance Contents Daily Control unit Function 2 Front control unit Front control unit Programme unit A1 2 The programme unit is electromechanical and has up to 10 fixed programmes depending on hysla.
Fit the drive belt and adjust the belt tension with the tensioner on one side of the motor.
These levels are called minimum levels. Connect the new motor to the cable and use straps to secure the cable. Drain valve 8 Input Function Pin 1: Replacing the heating elements Wen replacing the heating elements, there is a risk that water still left in the machine may flood onto the floor. The pump signal, on connection X Remember hylsaa “Delicate” is always without prewash.
When the lower part is filled with water, the lower part diaphragm pushes up the piston. The detergent is routed from the bottom of the compartment to the outer drum through the combo module immediately behind the compartment. manuql
Hitachi DV 20VC Handling Instructions Manual Page 4
Some single-phase machines are also equipped with a manual resettable overload protector mounted on the extract nylsa in the motor module. Y25 will flush in pre-wash and in main wash.
See the door interlock section of the manuao. It’s a community-based project which helps to repair anything. When the water rises in the drum and hose, the air in the hose compresses and, at two preset pressure levels shut-off levelstwo different alternating contacts in the pressure sensor are activated.
The maintenance interval should be adjusted according to machine usage. Apart from a level guard on the programme unit card, there is a level guard B2, connected to the door lock control A Locate and repair any leak. Instruction for pulley and replacing bearings 42 8 Fig.
For coin-operated models, insert the proper coins to start the machine. There are no Y22 valve on these machines.
Do not reach into the appliance if the tube is moving. Remove the door lock three holding screws. Jumper on C is bleaching function. If the water is very hard, check whether there mahual lime deposits on the heating elements. Push it down until it stops. Improper installation or servicing of Wascomat equipment will void the manufacturer’s warranty!