Home>FILTRES>KIT REVISION>KIT 3 FILTRES ADAPTABLE LOMBARDINI FOCS ET PROGRESS AVEC CARTOUCHE GO. (except where indicated in this manual). • Stop the engine before Diesel engine: LOMBARDINI mod. LDW FOCS • Keep the diesel engine running . FOCS Workshop Manual_cod. _1° ed_ rev. CHAPTER INDEX – This manual contains pertinent information regarding the repair of LOMBARDINI .
|Published (Last):||7 February 2006|
|PDF File Size:||19.24 Mb|
|ePub File Size:||9.56 Mb|
|Price:||Free* [*Free Regsitration Required]|
Wear protective gloves to avoid touching used oil. It is important to wear the personal safety devices prescribed by work safety laws and also by the standards of this manual. Fuel Pump Drive Rod Projection Once the check has been completed, remove the lombrdini and refit the O-ring.
Table of contents General Service Notes Make sure that the oil and the coolant are up to the maximum level.
Lombardini LDW 602 Manuals
When refitting tighten the screw at a torque of 80 Nm. To make sure that both the holes align appropriately use tool “” 1 inserting it into the glow-plug hole. Push rod A to the kombardini and keep it in this position; see figure. Maintenance – Recommended Oil Type – Refilling When re-fitting introduce the the new pre-combustion chamber into the cylinder head so that the side hole of the pre-combustion chamber aligns with the glow-plug hole.
Especificaciones Internacionales Para Lubricantes During remounting be careful with oil exhaust hose 4 that needs to be properly inserted into its housing on the cylinder head. Manufacturer And Engine Identification Remove the pressure switch, fit a union and connect a 10 bar pressure gauge.
Premisa – Clausula Enrretien Garantia Intake duct 9 10 8 2 Operation The main function of the E. Alternator Battery Charger Curve 12v 20a These fuels reduce the formation of paraffin in diesel at low temperatures.
Mitsubishi Motors Corporation May Run the engine to the maximum speed, that is rpm. Injector, Setting old Type Your consent to our cookies if you continue to use this website. Remove the closing caps 4 at the end and carefully clean inside. Check any wear in zone X where the piston rings operate and if it is greater than the 0. In case it is different from zero, adjust the regulator block nuts to move it, in relation to the rod 3, in the direction that goes from the flywheel to the timing.
The regions in which diesel normally has a low sulfur content are Europe, North America, and Australia. Tighten oil drain plug at a torque of 40 Ffocs.
Lombardini Diesel Engine Part Manual Ldw –
Warning Signs – Safety Instructions Do not check it before the engine has cooled down and, also in that case, open the radiator cap or expansion tank plug with caution. We share information about your activities on the site with our partners and Google partners: Cut the ring gear in several places using a chisel and remove it.
For engines with the injectors fixed with self-locking nuts, tighten the nuts at 23 Nm. Rotate the crankshaft until the unit injector cam lobe 2 forces the cam follower 1 to the highest position, then insert a suitable sized hardened pin into the hole 3 and rotate the crankshaft until the cam follower 1 is at the lowest position. Plunger Injection Pump Reassembly Screw special tool “” 1 into the pre-combustion chamber. Kawasaki Engine Service Manual To protect the environment in which we all live, Kawasaki has incorporated The hammer effect of the special tool will extract the pre-combustion chamber 3.
Explain the main result of this experiment and what physics you learned. At this point with lever 1 of fig. Liquid Cooled Diesel Engine done at a qualified diesel engine repair facility. Service and repair parts for Mitsubishi. Cylinder Head Assembly Unscrew the two fastening screws 2 of the lombardinii manifold from the engine crankcase.