The train communication network (TCN) is a hierarchical combination of two fieldbus for data transmission within trains. It consists of the Multifunction Vehicle Bus (MVB) inside each vehicle and of the Wire Train Bus (WTB) to connect the different vehicles. The TCN components have been standardized in IEC IEC and UIC have now been issued as a set of international standards to overcome this situation: IEC , the Train Communication Network. STANDARD. IEC. First edition. Electric railway equipment –. Train bus –. Part 1: Train Communication Network. Matériel électrique ferroviaire .
|Published (Last):||24 November 2013|
|PDF File Size:||11.70 Mb|
|ePub File Size:||16.44 Mb|
|Price:||Free* [*Free Regsitration Required]|
When iecc cost of ownership is considered, the cost of the hardware elements can easily be outweighed by additional engineering costs in the railways market with its small series. This explains why MVB and FIP have similar operation cyclic and event-drivenonly the arbitration method in case of multiple access differs, as MVB used a binary bisection mode relying of collision detection while FIP piggy-backed a “look-at-me” bit over periodic data.
But railways certification is costly and not always needed for uncritical applications such as comfort and passenger information. The MVB frames are not compatible with IEC fieldbus frames as it omits most of the preamble synchronization which is not required if zero-crossing detection is possible. The WTB operates cyclically to provide deterministic operation, with a period of 25 ms, used mainly for the traction control. Since connectors are exposed and can oxidize, a iev pulse is applied at connection establishment to evaporate the oxide layer, called fritting.
This is not due to the communication technology: When two train compositions join, the addresses are reallocated to form a new composition of vehicles with a sequential address. MVB is similar to FlexRayboth have the “process data”, which is called “static segment” in FlexRayand “message data”, which is the “dynamic segment” and are driven by a fixed TDMA scheme.
This separation is not always observed. The connector between the vehicles is the pole UIC connector. The plugs and sockets are the same as used by Profibus with two 9-pin Sub-D sockets per electrical device. The MVB standard was introduced to replace the multitude of field buses in the train equipment.
IEC | IEC Webstore
MVB for critical operation such as traction control and signalling in the driver’s cab, and LON for uncritical and slow data transfer, but low-cost connections such as passenger displays and diagnostics. There is no inauguration, the addresses are statically allocated.
Additionally more and more components are added to rail vehicles that need far more bandwidth than any field bus can provide e. Views Read Edit View history. The medium consists of a duplicated shielded twisted pair cable, which runs in the UIC cables between the vehicles.
Vehicles without WTB node “conduction vehicles” are not counted.
This was intentional as the fight between the field busses raged in the s and the decision of the IEC that any of the eight field busses was a standard did not help plug-compatibility.
Up to 32 addresses can be dynamically allocated. Rail technologies Serial buses Automation. The multifunction vehicle bus connects individual nodes within a 613375 or in a closed train set. While the WorldFIP, CANopen, Lonworks and Profinet are controlled by international manufacturer associations targeting a wide range of application, MVB was tailored to the rolling stock application, with the goal of plug-compatibility, and therefore allows no options.
Train communication network
The maximum distance is determined on the restriction of a maximum allowed reply delay of The difference came from the fieldbus physical ifc which assumes a phase-locked loop to decode the Manchester data, requiring a preamble to synthonize the decoder, while MVB operated principally with optical fibres where this method is useless, MVB’s decoding relies on zero-crossing detectors and Manchester pattern recognition.
Webarchive 613775 archiveis links CS1 German-language sources de. A unique property of the WTB is the train inauguration Zugtaufe in which the newly connected vehicles receive an address in sequence and can identify the vehicle side called port and starboard like in the marine so that doors open on the correct side.
The content of the periodic and sporadic frames is governed by the UIC standard. Interfaces are listed by their speed in the roughly ascending order, so the interface at the end of each section should be the fastest. The physical level is using transmissions at a 1.