6(&. iC-v SERVICE. MANUAL DISASSEMBLY INSTRUCTIONS. SECTION 4 . Specified Icom’s battery pack only (Operating voltage range; – V). View and Download Icom IC-V82 instruction manual online. Icom America VHF Transceiver, VHF Transceiver Instructions Manual. IC-V82 Transceiver pdf. View and Download Icom IC-V82 instruction manual online. VHF TRANSCEIVER . IC-V82 Transceiver pdf manual download.
Author: | Doutaur Virr |
Country: | Georgia |
Language: | English (Spanish) |
Genre: | Sex |
Published (Last): | 12 April 2008 |
Pages: | 49 |
PDF File Size: | 13.41 Mb |
ePub File Size: | 6.92 Mb |
ISBN: | 523-4-62559-344-2 |
Downloads: | 80368 |
Price: | Free* [*Free Regsitration Required] |
Uploader: | Bakus |
Duty cycle changes automatically.
Comments to this Manuals Your Name. This manual also for: See next set of instructions for setting tuning step size. This device complies with Part 15 of the FCC rules. D D Your call sign note programming You can add information to your own call sign such as oper- ating radio type or area.
Reset these frequencies, if necessary.
IC-V82, IC-U82 Downloads
By pressing ‘print’ button you will print only current page. When the reversed duplex mode is selected, the receive fre- quency shifts.
Ic-g82 it, continue to print. This setting can be set for each memory, call and VFO inde- pendently. Transmit at 5 W High at 2 W Middle 1. Total of codes are available.
The following items are additionally required. Page of 96 Go.
Microphone simple mode is used to change the function as- signments for keys in the optional HMA as below. Insert the connector firmly to avoid a bad contact. Don’t have an account? Cloning Cloning allows you to quickly and easily transfer the pro- grammed contents from one transceiver to another trans- ceiver.
Some options may not be available in some countries. To attach the belt mnual D Handstrap Not supplied Slide the hand strap through the loop on the top of the rear panel as illustrated below. SCAN channel selection, etc. D Memory scan watch While operating on a VFO frequency, memory scan watch monitors for signals in each memory channel in sequence, manuao 5 sec.
Icom IC-V82 Two-Way Radio User Manual
Ix-v82 auto repeater function is turned OFF. This setting allows you to set a minimum signal level needs icon open the squelch. Up to 6 transmit codes codes that you transmit are pro- grammable into code channels, C1 to C6, if required.
Transmit at 7 W High at 4 W Middle 2. DTMF memories are used to store phone numbers or control codes. Only tested and approved for use with genuine Icom bat- teries. Page 47 D Setting subaudible tones for tone squelch operation Separate tone frequencies can be select for tone squelch op- eration rather than repeater operation the same range of tones is available— see right below.
Repeater Operation Direct frequency input from the key- pad is also available. Pager selective code push [PTT] Answer back manual Set both transceivers to either code squelch or non-coded operation VFO mode and memory mode. Repeater Operation When the manusl duplex mode is selected, the receive fre- quency shifts.
The previously selected used weather channel is checked periodically during standby or while scan- ning. D Setting subaudible tones for tone squelch operation Separate tone frequencies can be select for tone squelch op- eration rather than repeater operation the same range of tones is available— see right below.
Please ask your dealer for details. The digital code or call sign squelch does not function while in a low- speed data communication.
The GPS message is transmitted from Tx message channels. Each of these channels can be individually programmed with op- erating frequency pgs. The position data can also be transmitted with a message to another station.
When the display type setting pgs. To print the manual completely, please, download it. Page 67 D D Auto Rx call sign Display When an individual station call is received, the calling station call sign can be indicated automatically.
IC-V82, IC-U82 Downloads – Icom America
Each receive and transmit frequency is shown in the table below with the following conditions; IC-V82 Input frequency: D D Tone information Some repeaters require different tone system to be accessed. The display type is selected in p. The offset and repeater tone frequencies are not changed by the auto repeater function. Even if the memory bank contents are cleared, the memory channel contents still remain pro- grammed. After waiting a few seconds, turn power ON again.
Operation is jc-v82 ject to the following two conditions: You can wait for calls from group members using the same tone and not hear other signals. Setting frequency In VFO mode, set the desired operating frequency with other desired settings, such as repeater and subaudible tone.
Program them in the same manner as regular memory channels. Page 55 D D Your call sign note programming You can add information to your own call mznual such as oper- ating radio type or area.
D D Auto Rx call sign Display When an individual station call is received, the calling station call sign can be indicated automatically. BPN will become exhausted.