Download DesignJet C Service from folder Printers DesignJet. DesignJet C Service Manual pdf. From folder: Printers HP DesignJet. View and Download HP C user manual online. DRAFTING PLOTTERS SERVICE MANUAL. C Plotter pdf manual download. Also for: Designjet c . Service Manual and more parts for CA DesignJet c printer.
|Published (Last):||11 October 2009|
|PDF File Size:||4.67 Mb|
|ePub File Size:||20.83 Mb|
|Price:||Free* [*Free Regsitration Required]|
Other features that are standard include: The speed of the drive roller can be reduced or speeded up by pressing the appropriate arrow button. Include system configuration in the report. State Messages Continued Message State Pen palette The pen source, pen number widths, and pen number shades you just en- saved tered have been saved as either Palette A or Palette B whichever you specified.
Disconnect the window sensor cable connector from the front panel PCA.
HP DesignJet 650 Printer series User Guides
Lower and hold the rollfeed cover about halfway open. If a PCA is revised in any way that makes it non-interchangeable with previously issued PCAs of a particular part number, a new part number is assigned to the revised PCA.
Insert the front end of the spring into the hole in the pinch arm assembly with the pinch arm 90 degrees from vesignjet normal position. Using a TORX T screwdriver, remove the screws that attach the front trim pieces to the left and right sideplates. Unable to determine warranty status.
HP DesignJet Printer series User Guides | HP® Customer Support
Disconnect the window sensor connector and the front panel cable connector from the front panel assembly. To remove the paper motor and drive roller gear, perform the following procedure: Press the small drive belt against the tensioner wheel in the belt tensioner to loosen the belt and slide the belt off of the motor gear.
Remove the front trim pieces. Remove the cutter assembly. Europe, Middle Designhet, Africa. Mispositioned Roll is mispositioned. Remove the left endcover.
Set the sled springs to their full upright position with the curved part of the springs resting against the stops inside the service station housing. Page Table Number C CA CA C C C C C C C C C C C C C Accessing Pens Figure shows you how to visually check the ink level in a cartridge.
Table lists the power require- ments for the plotters. Worded Error Messages Continued Message Media too small Media loaded for accuracy calibration or pen alignment is too small. Parts lists with associated illustrated parts break- down drawings are provided.
HP 650C User Manual
The pen carriage moves out from the pen service sta- tion at the left of the plotter and stops in front of the slot in the bail. Versions are iden- tified by their serial number and the date codes on their printed-circuit assemblies PCAs. PCAs having the same part number are directly interchangeable.
Unloading Sheet Media If difficulty in loading sheet media is experienced, an alternate method of loading is possible. Included are procedures that can be performed by the user. Page Service Station See Page Remove the front panel assembly. Dry time determines how long the plotter waits before cutting the plot.
Service Station See Page This process can take several minutes depending on the number of warranties being checked. Refer to Table for the seevice sizes usable on each plotter. In roll media opera- tions, the user can choose between continuous plotting or cutting plots off the roll automati- cally as they are completed.
The devices may be connected in a star or linear bus network. Accessories Depending upon the country of destination, the part numbers of items listed as English or U. Although multiple protocols may reside on an MIO, they are not simultaneously supported, only one protocol at at time can be used. Remove the left and right endcovers. Switch the plotter ON. Sheet Length Calibration All calibration procedures are accessible through the front panel menu structure. The main clock provides a For use in East and West Europe, Egypt.
This product was designated to be returned to HP. Remove the electronic enclosure cover. Access Pens brings the pen carriage out to the plotting area for pen access. When the front panel instructs you, lower the pinchwheel lever.
Real-time switching between plotting modes is not supported.