Categories Parts fuel Parts Hirobo Shuttle Sceadu SCEADU MANUAL Ask question. Description. SCEADU MANUAL. Browse this category: Shuttle Sceadu . Categories Parts fuel Parts Hirobo Sceadu Evolution SCEADU SWM INSTRUCTION MANUAL MANUAL. Browse this category: Sceadu Evolution. Beyond Sceadu!! SDX 50HPM kit. This swashplate accepts 90°HPM,. °SWM, and °SWM linkage for all Hirobo 50/90 size models.
|Published (Last):||14 July 2014|
|PDF File Size:||17.66 Mb|
|ePub File Size:||19.58 Mb|
|Price:||Free* [*Free Regsitration Required]|
No More Batteries coming loose in pirouettes!!!!!! I like the design of using the 32mm screws for the frames vice using self tapping Phillips head screws going into soft plastic frame spacers.
Delrin crank lock and homemade fan tool. Check your measurements when you are done.
Hirobo Shuttle Sceadu Evolution Manuals
Locktite and tighten the tail case screws. You are pretty much forced to use blank servo wheels here and drill holes. Sceadu Evo parts – Optional parts colour chart for the Evo. Tail boom ready to install.
If you have or have access to a dial point indicator, I highly recommend dialing in the run out of the start shaft. Unlike a Raptor, you need to make sure you leave the washer between the front bearing and the fan.
Very transparent for easy fuel level checks. Before your first flight, check for proper servo movement. Manua, flights, two autos, no broken parts; I decided to call it a day. Put a nut on one of the screws and tighten it down then stop and look at all the bearings and make manul they are properly captured in the seats and ensure that the fuel lines aren’t pinched in the frames.
Hi everyone I need manual for Hirobo Sceadu evo 50 – HeliFreak
The only online one that I am aware of has been taken off line, so hopefully this will become the place to go for assembling the Hirobo EVO Use two 10mm self tapping screws and install the bearing block to the right side frame don’t tighten these yet! Resisting the natural male urge to start tearing into things, I started as I always do by sxeadu the manual and reading it cover to cover.
Also, this is where you use the other ball that has a recess for the screw head. This is one area that it pays to check large egos at the flying field gate. scearu
It’s time to setup the throttle, and contrary to popular belief, this can be fairly simple. Don’t be afraid to experiment with different mixing arm, blade style, and paddle weight choices to see what works best for your style of flying. Replace the glow hiribo first to see if that fixes it.
Hirobo Shuttle Sceadu Evolution Instruction Manual Page 48
A belt driven tail utilizing a lower friction belt is standard equipment. Canopy and Decals ready to apply. The phenomenon has become common enough for most of us to refer to them as a piston punch tool.
Once you install the fan and prop nut, you can go ahead and put the back plate back on the motor, install the ball for the throttle arm and mount the clutch to the fan hub. Steps 11 and 12 involve the main grip assembly. HPM being the originally mechanical pitch version with a rocking cradle and SWM; this scfadu the upcoming ccpm control system that required a transmitter with electronic swashplate servo mixing to give both cyclic and pitch functions.
Most of the steps consist of mechanical drawings and are interspersed with helpful notes, but the builder is left to decide on his own assembly sequence.
Vintage RC Helicopters – Hirobo Sceadu
Same setup here with the offset balls on the servo wheel. If your engine starts running rough after running well for a period of time, do not adjust the needle valves immediately. Notice that the balls are slightly offset on the servo wheel. The comments, observations and conclusions made in manuxl review are solely with respect to the particular item the editor reviewed and may not apply generally to similar products by the manufacturer.
Put the two plastic spacers on either side of the tail drive gear where the lower mast bolt goes through and hirono the lower mast bolt with a nyloc nut. Fuel tank assembly 9.
The first step is to setup the transmitter.