Regulation No 26 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of vehicles with. ECE R26 Regulation (03 Series, ) “The uniform regulations on vehicle chapter and section numbering betw een this standard and the ECE R ECE UNIFORM PROVISIONS CONCERNING THE APPROVAL OF: VEHICLES WITH REGARD TO THEIR EXTERNAL PROJECTIONS Incorporating.
|Country:||Central African Republic|
|Published (Last):||8 February 2012|
|PDF File Size:||17.33 Mb|
|ePub File Size:||7.67 Mb|
|Price:||Free* [*Free Regsitration Required]|
Draft new Regulation No. Rce the ornament is mounted on a base, this base is regarded as belonging to the ornament and not to the supporting surface.
Technical service conducting approval tests: The administrative department which has granted approval of the vehicle type shall be notified of any modification of the vehicle type. Jacking Brackets and Exhaust Pipes 6.
Revision and, if applicable, the procedure contained in Paragraph 7. The Type Approval Authority may carry out any test prescribed in this Regulation. Retracting headlights shall meet the provisions of Paragraph 6. If a Party to the Agreement applying this Regulation withdraws an approval it has previously granted, it shall forthwith notify the other Contracting Parties applying this Regulation by means of a communication form conforming to the model in Annex 1 to this Regulation.
UN R41 Motorcycle Noise Motorcycle Noise Uniform Provisions Concerning the Approval of Motor Cycles with regard to Noise The proposal for the 04 series of amendments, adopted at the June Forum session, will be posted as Revision 2 to the regulation pursuant to the completion of administrative formalities.
Production Definitely Discontinued Wheel fixing The use of vehicle manufacturer’s replacement wheel fixing components is recommended. In determining the floor line, the jacking points, exhaust pipes or wheels shall not be taken into consideration. Projecting visors and rims shall be permitted on headlights, provided that their projections, as measured in relation to the external transparent surface of the headlight does not exceed 30mm and their radius of curvature is at least 2.
The regulation was adopted during the November WP. The material used for the wheel fixing components shall be at least equivalent to the vehicle manufacturer’s replacement wheel fixing components.
Licenses and Certificates
An approval number shall be assigned to each vehicle type approved. UN R16 Safety belt systems. The assembly instructions shall contain sufficient information to ecr the approved components to be mounted on the vehicle in a manner that complies with the relevant provisions of Paragraphs 5. The provisions of the above paragraphs 5.
EUR-Lex Access to European Union law
Figures 5 and 6 show examples of the use of this procedure. The Type Approval Authority which has granted type approval may at any time verify the conformity control methods applicable to each production unit.
The ends of the bumpers shall be turned in towards the external surface in order to minimise the risk of fouling. UN R63 Moped Noise.
When the vehicle is travelling in a straight line, no part of the wheels other than the tyres, situated above the horizontal plane passing through their axis of rotation shall project beyond the vertical projection, in a horizontal plane of the external surface or structure.
With regard to the design basic contour, dimensions, inset, material type and quality and so on and service life they fully correspond to vehicle manufacturer’s replacement wheels. Brugmann — Bte 2, B Brussels, Belgium. The first two digits of the approval number indicate that, at the time of approval, Regulation No. In every inspection, the test books and production survey records shall be presented to the visiting inspector.
One for each impact position. Communication concerning the approval or refusal or extension or withdrawal of approval or production definitely discontinued of a vehicle type with regard to its external projections. The distance between two consecutive elements of grilles and gaps shall be determined according to the method described in Paragraph 4 of Annex 3 to this Regulation. Rim contour shall ensure the correct fitting of tyres and valves.
Notice of approval or of extension or refusal or withdrawal of approval or production definitely discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation by means of a communication form conforming to the model in Annex 1 to this Regulation. Wing nuts shall not be allowed.
UN Regulations provide uniform requirements for the approval of motor vehicles and equipment.
– Transport – UNECE
Vehicles f26 with hydropneumatic, hydraulic or pneumatic suspension or a device for automatic levelling according to load shall be tested with the vehicle in the most adverse normal running condition specified by the manufacturer. Modification of a vehicle type and extension for approval 8.
Drawings, with dimensions, of the bumpers and, where appropriate: Ventilation holes check An approved wheel shall not reduce the brake efficiency in comparison with a manufacturer’s replacement wheel.
Uniform Provisions Concerning the Approval of: