Example Cisco MDS Switch Default Port License Configuration. switch# show port-license Available port activation licenses are 0. Cisco MDS Family Quick Configuration Guide. OL Using the Switch Setup Utility Verifying the Module Status CHAPTER. 3. Configuring. Note If a Cisco MDS or switch is used as a core switch, only a nontrunking F PortChannel is supported. Trunking is not supported on.
|Published (Last):||11 August 2014|
|PDF File Size:||7.8 Mb|
|ePub File Size:||2.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
It is worded as if it is a requirement but it is in fact not. I am not sure if this is valid. About System Message Logging properly configured system message logging server.
The opinions expressed in this blog are entirely my own and should not be taken as the opinion of my employer. In this case, using the proxy initiator mode simplifies the configuration. When you join two switches belonging to two different stable fabrics that have overlapping domains, the following cases apply: Have a few different people read that and I think you will see where I am coming from.
This should be made more clear. Should be 8 base ports, which can goto 8 or 16 additional ports. I am not sure that the statement in bold is correct.
Page Figure shows incorrect ip default-gateway Page States in one bullet: The autoreconfigure option takes immediate effect at runtime.
Leave a Reply Cancel reply You must be logged in to post a comment. This can mean several configuration tasks for each iSCSI host. You must be logged in to post a configurationn.
Unofficial Cisco MDS Release 3.x CLI Config Guide Errata
configuratiion Caution The span drop-threshold can be changed only if no span sessions are currently active on the switch. Although it can be configured it has no effect. These pages talk about an active mode of fcanalyzer. This is not true. Reconfiguration as in changing of domains is always disruptive. Page Information is repeated twice on the same page: This is not correct as this does not work.
I think what is meant here is: This situation can require several configuration tasks for each iSCSI host. If a domain is currently isolated due mdd domain overlap, and you later enable the autoreconfigure option on both switches, the fabric continues to be isolated.
Page shows with 8 base ports 8 licensed for growth.
You basically give the same settings for the IBM configurationn switch but this is a 24 port not a 20 port. This blog is mostly about my pursuits in Data Science. On the same page I find this block of text very vague and confusing: Previous blog entries also dealt with storage, compute, virtualization and professional services.
Unofficial Cisco MDS Release 3.x CLI Config Guide Errata – Maximum Entropy
If you enabled the autoreconfigure option on both switches before connecting the fabric, a disruptive reconfiguration RCF will occur. Obviously there was a part of this paragraph that got chopped off somewhere. You cannot mix ingress and egress interfaces in the same SPAN session. ciso
Proudly powered by WordPress. This is not correct. Testing indicates that this is in fact enabled by default. The default authentication port is There is no information contained in the example given that shows the configuration or enabling of FCIP interfaces.
FCIP uses different ports. This page incorrect states that fcns reject-duplicate-pwwn is disabled by default. Page Document states: Certainly there is either a mistake in the wording or the example.
Then states two bullets later: A disruptive reconfiguration may affect data traffic. If you assign port number for physical portshow can you assign for ports ?
Cisco Documentation team has internally re-written this as: This is very redundant and can be combined into one bullet. If you do not need explicit LUN access control, using the proxy initiator mode simplifies the configuration. This however would be very nice to have in the documentation for IPS network simulator, an example showing complete configuration of Gigabit Ethernet interfaces and FCIP tunnels to go along with the Network Simulator.
IP routing does not mdw to be enabled, unless there is a specific topology where IP routing is necessary.
The way its written sounds like if you have a large scale deployment where you need explicit LUN access control you can use proxy-initiator, but its really the opposite.