The Chroma A W and A W electronic load mainframes accept the user-installable A series load modules for easy system configuration. user can perform on line voltage measurement controlled instructions via RS- C or GPIB The Chroma W and W electronic load. File, CHROMA Series, , Mainframes X, Operation Share technical documentation including product manuals, getting started guides, and.
|Published (Last):||13 January 2007|
|PDF File Size:||12.21 Mb|
|ePub File Size:||3.80 Mb|
|Price:||Free* [*Free Regsitration Required]|
If your application requires a greater power or current capacity than one module can provide, you have to connect load modules in parallel in CC or CR mode. Barry McDaniel 1 years ago Views: There is a double pole RC filter of input voltage, so high frequency parts will be removed.
The nominal output power is More information. Chroma Manual Even though other OSes might be patible as well, we do not remend apying this release on atforms chroma a user manual other than the ones specified. In remote mode programmed value cannot be over boundary. This warranty is in lieu of all other warranties, expressed or implied, and no representative or person is authorized to represent or assume for Chroma any liability in connection with the sale of our products other than set forth herein.
The line fuses will Overcurrent When Load is operating in CR or CV mode, it is possible for a module to attempt to sink current more than it is rated for. The Chroma Mainframe has room for four single-width Loads, or two double-width Loads In addition, the remote control commands will be compatible between the and the A series without needing to re- writing any remote control programs.
Operation & Programming
Without the written permission of the copyright holder. Updated versions of this document More information. To make this website work, we log user data and share it with processors. When local operation is in effect, you can select a channel, and use the display as well as keypad on the front panel to control the Load.
If you have not done thus, Load manuap shut down, or fuse for remote xhroma in Mainframe will be broken.
The Load module also executes a self-test that checks firmware and communication with Mainframe. Immediately after power is applied, local operation will be in effect. Load modules occupy either one or two slots. The nominal output power is. Press MODE key first, then ,anual or key to select the current range. The change of modes will affect the module, so will the change of range.
Voltage Ranges Low, High There are two voltage ranges for voltage measurement and Von voltage setting. Chroma assumes no liability for secondary charges or consequential damages and in any event, Chroma’s liability for breach of warranty under any contract or otherwise, shall not exceed the purchase price of the specific instrument shipped and against which a claim is made.
Special disclaimers apply to these instruments. The unit has been factory set to the correct line voltage. If the instrument is defective as a result of misuse, improper repair, or abnormal conditions or operations, repairs will be billed at cost.
Chroma DC Electronic Load Mainframe With Manual O1 | eBay
Each program has ten sequences. Unlike conventional supplies with fixed output ratings. Power Cord, Manual Load Module: The actual value of electronic short is dependent on the mode and range that are active when the short is turned on.
The load can be dhroma in constant current, constant voltage, constant power and constant resistance.
The A load module uses a photo coupler for isolation between the. The A series has a self-diagnosis routines to maintain instrument performance. Dynamic Loading and Control Amnual A loads offer high uswr, programmable dynamic load simulation and control capability. A Cheat Sheet Open Loop Vector The following procedure is a supplement to supplied with this equipment and will guide the user in properly wiring the A and. Add to Inquiry Cart Data Sheet.
There are two operation modes for Von control. Transportation to the factory or service center is to be prepaid by purchaser. Click here to unsubscribe. This feature reduces overall noise level because the fans do not always run at the maximum speed. The low range is used for input voltage in low voltage range while the high range for input voltage over low voltage range. Figure The Front Panel of the Electronic Load On the front panel of the electronic load as shown in Figure there are two groups of keypads.
Mainframes accept the user- installable A series load modules for. Determine the position for the Hands-free phone in the elevator phone More information. There are also higher wattage modules that may be mixed and matched for an even more versatile system.
Chroma 6314 DC Electronic Load Mainframe With Manual O1
STATic function checks the stability of output voltage from a power supply. Turn on the Load by the power switch on the front panel of the Mainframe and observe chroa display. In CV mode it is equivalent to the programming of zero voltage.
All load modules may be configured to work synchronously, to test multiple outputs simultaneously, thus simulating real life applications. Because some Load has two channels in one module, channel 1 and 2 are always on the farthest left slot of the Mainframe, and channel 7 and 8 on the farthest right. The waveforms programmable parameters include: Chroma A Programmable Electronic Load integrates microprocessor capabilities into each load module and mainframe to provide simple and accurate parallel operation to optimize the speed and control among chroa load modules.
Mankal Ranges Low, High Resistance can be programmed in either of the two ranges, low range and high range.