Cardax FT Controller – Download as PDF File .pdf), Text File .txt) or read online. Installation Guide. Cardax FT Controller CAUTION This equipment contains components that can be damaged by electrostatic discharge. Ensure both you. The Gallagher Controller supports the following door readers: > Cardax IV Prox (Mifare, kHz, TIRIS). > Cardax IV Prox Plus (Mifare, kHz,. TIRIS).
Author: | Yomuro Akirn |
Country: | Philippines |
Language: | English (Spanish) |
Genre: | History |
Published (Last): | 13 June 2010 |
Pages: | 155 |
PDF File Size: | 19.30 Mb |
ePub File Size: | 7.77 Mb |
ISBN: | 731-1-85755-957-7 |
Downloads: | 74790 |
Price: | Free* [*Free Regsitration Required] |
Uploader: | Voodookree |
Plug-in ModemThe Cardax FT Controller has an on-board connector Serial for a plugin modem part number C which is purchased separately from the Controller Ensure both you and the equipment are earthed before beginning any servicing.! One GBUS port to support: Close and lock the Cardax FT Controller cabinet door within ten seconds, i. Communication between Cardax FT Controllers and lower level hardware items uses two Cardax-proprietary data communication formats.
Providing flexible configuration options to meet specific site requirements, Gallagher Controllers: Controller The Gallagher Controller is specifically designed to support access controlled doors and integrated intruder alarms.
Each device attached to a Cardax FT Controller must be allocated an “address”. Label each cable as you remove it. Refer to the previous section “Component layout” for the location of the plugs.
Cardax Ft Controller pdf
Operating temperature Humidity Maximum number of Cardaxx lift the Controller clear of the Cabinet. However, this DC voltage out will be approximately 1 volt lower than the voltage supplied to the Cardax FT Controller Boot code monitor running. This picture is not to scale, therefore use the measurements provided. The security of the installation ultimately depends on the way the Cardax FT Cabinet is installed. The section titled “Run LED” later in this Installation Note details the different meanings of the various flash sequences.
Gallagher Controllers | AES Group Ltd.
Flash Slow Fast 1 flash 2 flashes Sequence timing Meaningms on, ms off Controller is searching for software FTS files ms on, ms off 4Hz flash ms on, ms off 1Hz flash 2 flashes – pause each flash is 50ms on, ms off, 1.
Published on Oct View 1. These contacts close when the Controller is powered up, and remain closed until either the power is removed or there is a ‘Catastrophic Failure’. Both variants of the Controller can operate on their own, or can have an optional Reader Module part number C or C connected. Controller will reject WWW connections.
This operation can only be reset by the factory of manufacture. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. Unused Unused Boot normally.
The sequence completes fairly quickly but it is important you ensure the LED finishes indicating the “normal running” sequence. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
A dial-up modem may be used for communication if network communications are not available.
Click the OK button. Assigning an IP address acrdax via a web browser When the Cardax FT Controller is started reset or power-up with DIP switches 2 and 3 enabled, the Controller uses the following default addresses: When the Cardax FT Controller is re-powered after servicing and is operating correctly, the optical tamper detectors will be re-initialised.
The Cardax FT Cabinet should be installed in a secure, internal location. Cardax FT Key Strengths.
Optical tamper detectorsThe front optical tamper detector will sense when the Cabinet door is opened. The red Run LED flashes in the following sequence: Note that this cable type is only suitable for the communications circuits. Shimano tiagra flight deck 9 speed manual Acer travelmate lci driver Ni circuit design suite keygen Documents. Looking at the Controller it will be obvious that the there is 600 ethernet activity on either ethernet connection, as the RJ45 connector LEDs will not be operating, and the Controllers run LED will be in 2 flash.
Cardax Ft Controller 6000pdf
On-board connections are provided for:. Press the Enter key on your keyboard. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Set switch 2 to OFF open.
On-board connections are provided for: Unused For factory testing only. Initialise the Cardax FT Controller This port is provided for external communications to be connected to the system.
This means in the event of network communications being disrupted, security is maintained on site.