ASTM D4414 PDF

ASTM D – Medición de EPH – Download as PDF File .pdf), Text File .txt) or read online. Standard ASTM D The following devices are in accordance with ASTM D ZMK – Road Marking Control Kits. Specially designed for road . Technical Specification. STANDARDS: ASTM D A, AS/NZS , BS CB,. ISO A, ISO B, JIS K , NF T, US.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard ASTM D4414

Wet film thickness gauges are also known as wet film gauges, notched gauges, step gauges and WFT combs. All the other teeth or notches on the same side are of shorter lengths than the outside teeth or notches and represent different distances from the outside edge zero datum teeth.

Add to Alert PDF. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards.

How to Use a ‘Wet Film Thickness’ Gauge

The wet film thickness WFT of the coating lies between the values of the smallest un-coated dry tooth or notch and the largest coated wet tooth or notch. Historical Version s – view previous versions of standard.

Consequently, the results from the notch gage are not to be used to verify the nonvolatile content of a coating. It measures the thickness immediately after the coating has been axtm on the material. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The teeth or notches of the gauge should be ‘dragged’ at ninety degrees through the coating and the thickness of the powder will lie between the values of the smallest tooth or notch that has powder ‘clinging’ to it and the largest tooth or notch that has no powder ‘clinging’ from it.

The gauge may now be read to determine the wet film thickness.

ASTM D() – Standard Practice for Measurement of Wet Film Thickness by Notch Gages

Correction of the film after it has dried or chemically cured requires costly extra labor time, may lead to contamination of the film, and may introduce problems of adhesion and integrity of the coating system. The mode of operation is similar to measuring ‘wet’ coatings. Model A Gauges The gauges are precision manufactured from hardened grade stainless steel. Also notched gages can be very useful in the shop and field for determining the approximate thickness of wet films over commercial articles where size s and shape s are not suitable for measurements by other types of gages.

The values given in parentheses are for information only. Subscription pricing is determined by: These gauges are not designed as ‘throw-away’ items and should not be compared to gauges that are ‘printed’ or silk-screened.

Wet film thickness is measured to determine the correct dry coating thickness. Caltech’s wet film thickness gauge is designed to measure accurate liquid coating thickness in the easiest and fastest manner. Notch gages may, however, be used on nonuniform surfaces, like concrete block, that are too rough to use the Interchemical and Pfund gages.

Disposable plastic wft gauge is designed for once only use, simply place in the wet paint note the wet paint thickness, Allow paint to dry and retain for future ISO record or customer requirements. Such a gage is applicable to coatings on flat substrates and to coatings on articles of various sizes and complex shapes where it is possible to get the end tabs of the gage to rest in the same plane on the substrate.

This standard is also available to be included in Standards Subscriptions. The overall size of the gauges is 2. These gauges are also commonly known as: When wet film thickness is measured with the gauges on rough substrates, the thickness measurements made will most likely be from the surface ‘peaks’ and the wet film thickness measurement will represent the minimum overall wet film thickness. All the WFT gauges are highly ecomical priced.

The thickness of dry powder coatings may also be measured with these type of gauges. Wet Film Thickness Gauges are designed to quickly and easily measure the thickness of coatings immediately after they have been applied to a substrate. Please first log in with a verified email before subscribing to alerts. Wait several seconds to allow the teeth or notches of the gauge to become ‘wetted’ by the coating, then withdraw the gauge vertically keeping it at ninety degrees to the substrate.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Each gauge has eight different measurement notches. WFT Gauge can also be used to measure powder coating thickness before it goes through curing. If quick drying coatings are to be measured, quickly perform your measurements to avoid errors that may be caused by curing.