L Stainless Steel Sheet. ASTM A Characteristics. / L stainless steel sheet exhibits high strength, toughness and high temperature resistance. The following alloys meet the ASTM-A standard. Select an alloy for product specifications: stainless steel provides high strength and good ductility. ASTM A Standard Specification for Annealed or Cold-Worked _机械 /仪表_工程科技_专业资料。ASTM A Standard.
|Published (Last):||19 December 2009|
|PDF File Size:||13.59 Mb|
|ePub File Size:||4.36 Mb|
|Price:||Free* [*Free Regsitration Required]|
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? The noncontrolling factor normally will exceed considerably the speci? This specification astn austenitic stainless steels in the annealed and normally required cold-worked conditions.
In case of dispute, the offset method of determining yield strength shall be used. This standard has been approved for use by agencies of the Department of Defense.
The choice of test method for materials in conditions other than annealed shall be at the option of the seller. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
The steels shall adhere to specified chemical composition requirements. B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci?
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
C Annealed material asrm naturally meets mechanical properties may be applied. Historical Version s – view previous versions of standard. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
The values given in parentheses are for information only. They shall be formed in different shapes such as sheets, strips, plates and flat bars. Hard Elongation in 2 in. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. HardC Elongation in 2 in.
Mechanical properties such as axtm strength, tensile strength, elongation, hardness, and bending shall be determined. Material Test Report and Certi? This revision of Speci?
A superscript epsilon e indicates an editorial change since the last revision or aa666. ICS Number Code Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
The values given in parentheses are for information only. Link to Active This link will always route to the current Active version of the standard.
ASTM-A Alloys | E. Jordan Brookes Company
A — 03 Standard Speci? D PSS means plate, strip, sheet. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Only annealed conditions of grades speci?
Originally approved in Last previous edition approved in as A — Asym on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties. An atsm method of determining? The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test. Number of Tests 8. Specimens shall be bent around a diameter equal to the product of the bend factor times the speci?
A number in parentheses indicates the year of last reapproval.
ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
Current edition approved Oct. This abstract is a brief summary of the referenced standard. One bend test shall be made from one end of each coil. Your comments will receive careful consideration at xstm meeting of the responsible technical committee, which you may attend.
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. B Maximum unless otherwise indicated.
Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use. Rockwell B 95 95 However, in the case of dispute, tests shall be made by pressure.