Learn about ASTM A steel mechanical tubing and Atlas Tube’s manufacturing capabilities regarding this product for OEM applications. CALIFORNIA. Arrow Route. Rancho Cucamonga, CA WWW. ASTM A TUBING SPECIFICATIONS. TOLERANCES. ASTM A/AM: Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing.
|Published (Last):||15 August 2015|
|PDF File Size:||11.59 Mb|
|ePub File Size:||15.4 Mb|
|Price:||Free* [*Free Regsitration Required]|
C Where the ellipsis appears in this table, the tolerance is not addressed. The twist in square and rectangular tubing may be measured by holding one asfm of the tubing on a surface plate and noting the height of either corner of the opposite end of same side above the surface plate. If secondary melting is employed, the heat shall be de? If the results of the mechanical tests do not conform to the requirements shown in the table, retests shall be made on additional a5133 double the original number selected, each of which shall conform to the speci?
Aastm values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. B,C Outside Diameter, in.
NOTE S1—A lot shall consist of all tubes, before cutting to length, of the same size and wall thickness aa513 are produced from the same heat of steel and, when heat treated, subjected to the same? Nondestructive Electric Test S8. If no grade is speci? A Wall Thickness in. A — 07 Standard Speci? Bar coding is acceptable as a supplementary identi? For particular applications, properties may be adjusted by negotiation between purchaser and producer.
The squareness of sides is commonly determined by one of the following methods. Should the order specify that tubing be shipped without rust retarding oil, the? Flash-In-Tubing is produced to outside diameter tolerances and wall thickness tolerances only, and the height of the inside welding?
Referenced Documents purchase separately The documents asrm below are referenced within the subject standard but are not provided as part of the standard.
Tubes for Cylinders S1. This tolerance applies to the speci? Tubing heavier than 16 gage will normally be shipped loose, bundled, or in secured lifts. Twist may also be measured by the use of a beveled protractor equipped with a level, and noting the angular deviation on opposite ends, or at atm point throughout the length. Such defects as seams, slivers, pits, laps, etc. Product and Package Marking Hardness and Tensile Requirements S5.
Heat and product analyses shall be made to determine the percentages of chemical elements, to which the steel specimens shall conform to. Outside diameter burr to be removed for measurement. A superscript epsilon e indicates an editorial change since the last revision or reapproval. When steel of different grades is sequentially strand cast, identi? Originally approved in For grades of round tubing not shown in Table S5. F Birmingham Wire Gage.
A Square Carbon Steel Tube | Alro Steel
For welded tubing the notch shall be placed in the weld, if visible. For each additional 10 ft or fraction thereof over 24 ft, an additional allowance should be made of plus or minus 1? This standard has been approved for use by agencies of the Department of Defense.
No cracks or breaks q513 the base metal shall occur until the distance between the plates is less than one third of the original outside diameter of the tubing, but in no case less than? Workmanship, Finish, and Appearance Said notch shall have a depth not exceeding ?
Rejection Provisions for Government Orders S Hydrostatic Test Round Tubing S7. Committee A01 has identi? A Wall Thickness 38? The x513 thus determined shall correspond to the requirements of Tables When specified, tubing shall be coated with a film of rust retarding oil before shipping. Permissible variation in outside and inside diameter for tubing made from hot-rolled steel that has been Drawn Over a Mandrel DOM for closer tolerances are shown in Table 5 with wall tolerances shown in Table 7.
Approved May 1, 1 Revised 5. This condition is available in Types 1a, 1b, and 2 over 11? Type 1a, as-welded from hot-rolled steel with mill scale ; Type 1b, as-welded from hot-rolled pickled and oiled steel mill scale removed ; Type 2, as-welded from sstm steel; Type 3, sink-drawn hot-rolled steel; Type 4, sink-drawn cold-rolled steel; Type 5, drawn over a mandrel; and A5513 6, special smooth inside diameter.
A513 Square Carbon Steel Tube
Tubing shall be free of injurious defects and shall have a workmanlike finish. Special Smooth Inside Surface S4. Round A5133 Wall thickness 34 Outside Diameter, in.
Combining values from the two systems may result in non-conformance with the standard. When an oxide-free surface is speci?
Evidence of lamination or burnt material shall not develop during the? This specification covers round, square, rectangular, and special shape electric-resistance-welded carbon and alloy asgm mechanical tubing produced by hot- or cold-rolling.