2008 BUELL-FIREBOLT-SERVICE-MANUAL FILETYPE PDF

View and Download Buell XB Series service manual online. XB Series Motorcycle pdf manual download. See a Buell service manual for proper torque values. Aftermarket . Typical Buell V.I.N.: Ulysses Models Ignition System: XB Models. ITEM. DATA. T+ .com/

Using a slide hammer action, remove the slider fork 27 If damper locknut has been moved, proceed with the fol- lowing disassembly and assembly procedures for setting from the outer tube To minimize swirl marks, cleaning should be done when motorcycle is cool and parked in the shade.

Transmission sprocket nut 2. Vertical Headlamp Adjustment Fastener: Grab headlamp grille on either side and spread to tiletype from headlamp assemblies. Disconnect fuel pump connection and remove connector sm from subframe tail assembly. This voltage reading Install air cleaner assembly. The socket and pin buell-firebolt-service-maunal of all other connectors are inter- changeable, that is, the black may be mated with the gray, since the alignment tabs are absent and the orientation of the external latch is the same.

Muffler Mounting System Inspect seats for cracking, chipping or burning. Install footpeg mount 3.

Remove body work fasteners 2. Remove two screws 2 to detach tail Check tail lamp for proper operation. Contact a Buell dealer Remove lower triple clamp pinch fasteners, two per side.

Route neutral indicator switch and the oil in-lbs Negative battery cable 2.

Buell Firebolt Service Manual

Tighten but do not torque. Pull on windshield to verify attachment. Rear Isolator Bolt Figure Remove the Spacer Figure Raise tang to install Figure A To prevent leaks, lubricate the o-rings before installation. Loosen adjuster nut 2 and remove and farther away than they actually are.

2008 Buell XB Models Service Repair Workshop Manual DOWNLOAD

Insert bullet connectors and wiring Attach bullet connectors on turn signal wires as shown in through hole in front module. Excessive play bearing to fly apart, which could result in death or serious or roughness indicates worn bearings. NOTES Position the lower idle control cable barrel in the throttle On all Buell XB Models, buell-fireolt-service-manual throttle cables have filetjpe wheel of the throttle body and then slip the elbow into threaded adjustments on both ends of the cable.

Buell Models except Blast Figure The oxygen sensor O2 Sensorlocated in Install sensor lead into retainer. Low visibility of rider can result in locked in position.

Buell XB 2008 Series Service Manual

Place pressure plate, diaphragm spring, adjusting screw sm assembly with new retaining ring and spring seat onto clutch pack. Rotor mounting fasteners must be seated into drive Install new washers 9. Left tail section 6. Install pinion gear spacer and pinion use your hand to check for air leaks or to determine air gear on pinion shaft. For maximum strength, integrity and longevity, avoid a fixed idler pulley that maintains the desired tension throughout over bending, twisting, crimping, pinching, kinking or prying suspension travel and life of the belt.

Surface must be smooth and free of debris or old gasket material. Wheel buell-firebolt-service-manyal Figure A Wiring Diagram Symbols Either end may be installed into the filter mount. Apply Buell-firebolt-service–manual blue to Install components that were removed buell-firebolt-service-manul engine as were swingarm pivot shaft pinch bolt threaded insert and necessary for service prior to installing engine in frame. Latch screw Figure Squeeze handle of crimp tool until tightly closed.

To remove secondary locks, insert end of small flat blade screwdriver 1 under lip of locking sm wedge 2 and gently pry up secondary lock. Unthread axle buelll-firebolt-service-manual 15 threads to release tension from drive belt.

Slide idler buell-firebolt-service-mznual bracket 4 off studs 3. Wire cover Figure Install Nut Typical Figure An unbalanced motorcycle can fall, which could result in death or serious injury. Insert lap shaft with arbor assembled through pinion bearing bushing and into guide sleeve.

Rear intake cover fasteners with nylon washers 2 4.